GS 900 / GS 900 DELUXE


  • The Scooter is suitable for adolescents and adults. It is not a toy, but sports equipment for physical training.
  • Use with caution on a flat, clean, dry surface and, if possible, away from other users, and obey the road safety rules.
  • Check local laws regarding scooter use, respect all the traffic rules and signs.
  • Stay away from other pedestrians or users on public roads.
  • Best when used on a flat, dry surface free of gravel and grease. Avoid bumps and drainage crates that might cause an accident.
  • Warning! Personal Protective equipment should be worn: wrist protectors, gloves, knee pads, helmets and elbow pads should be worn.
  • Maximum weight: 100kg


USING THE SCOOTER Before and after each use:

  • Check the height of the steering system and make sure that the nuts are tightened and the handlebars and front wheel are perpendicular.
  • Check all of the connection elements: the brake, the release system of the steering column and the wheel axles must be correctly adjusted and must not be damaged
  • Also check the tire wear.


  • A brake is located at the rear, when necessary, press down on it to slow down. Press down gradually to prevent skidding or loss of stability. The metal or aluminium brake may heat up after multiple uses. Avoid touching it during and after use.


During use:

  • Standing on the scooter, with one hand on each handle, push with one of your feet to move forward. Proceed with caution at the start.
  • Always wear shoes and we strongly recommend wearing pants and long sleeve shirts to avoid injury if you fall.
  • The scooter does not include any headlights or lights. It is therefore not suitable for use at night or during periods when visibility is limited.
  • Do not use on wet days, or on wet ground.


Assembling the product:


  1. Loosen the screws of the clamp with the allen key provided.
  2. Insert the handlebar into the stem of the fork while paying attention to the position of the base.
  3. Position the clamp with the screws on the back side of the tube.
  4. Tighten the screws of the clamp with the allen key provided.
  5. The tightening of the screws should be progressive and successive (between 5 to 10 times), so as not to damage the screws and the clamp, until they are locked in place.
  6. Those who do not have enough strength to tighten the screws with the allen key provided might find that using a different tool may be easier.
  7. GS 900 & GS 900 DELUXE included 2 pegs respectively. Install them by loosen the bolts next to the wheels. Take the correct length of peg axle for front or back, and put it through, choose if you want to mount your pegs on the left or right side depending on your personal preference and style. Send the axle bolt right through the opening gently and retighten the bolts next to the wheels.

After each use make sure that the screws are tightly in place so that the handlebar doesn’t detach itself.



General instructions

To use with suitable protective equipment, including a helmet, shoes, elbow, wrist and knee protectors. Teach the child how to use it safely and responsibly. Before and after each use: To prevent pinched fingers, don’t get your fingers stick underneath plastic head tube cover and front fork.



Care / Maintenance: regular maintenance is a safety commitment:

Wheel bearings: avoid going through water, oil, or sand as this can damage wheel bearings. To look after the wheel bearings, systematically check that the wheels turn properly by turning the scooter upside-down and using your hand to spin the wheels. if the wheels do not spin, they must then be removed to check their condition.


First unscrew the wheel axle, remove the axle, and detach the wheel, then carefully push the two-wheel bearings out of their housing:

  • if they are chipped or dented, new ones should be bought
  • if there is no visible damage, they must then be oiled.

To do this, remove all traces of grease, mud or dust with a kitchen towel or cloth, and re-oil them with:

  • a grease spray or
  • by leaving them to soak overnight in oil [turn them several times in the oil first].

Then reassemble the wheel bearings and axles, followed by the wheel, onto the scooter. proceed in the same manner for the other wheel.


Wheels: the wheels wear down with time and can be pierced if overly used on rough surfaces. The back wheel on which the brake is applied is particularly affected after several hours of braking. In the interests of safety, they should be checked regularly and changed if necessary.


Modifications: the original product must by no means be modified except for the maintenance-related changes mentioned in these instructions.


Nuts, axles and other self-locking fixings: these should also be checked regularly. They can become loose after a while in which case they should be tightened. They can become worn and not tighten properly, in which case they should be replaced.


Additional Info

For questions and inquiries please contact us at:



The manufacturer warranties this product to be free of manufacturing defects for period of 2 years from date of purchase. This limited Warranty does not cover normal wear and tear, tire, tube or cables, or any damage, failure or loss caused by improper assembly, maintenance, or storage. This Limited Warranty will be void if the product is ever

  • used in a manner other than for recreation or transportation;
  • modified in any way;
  • rented

The manufacturer is not liable for incidental or consequential loss or damage due directly or indirectly to the use of this product.

Globber does not offer an extended warranty. If you have purchased an extended warranty, it must be honoured by the store at which it was purchased.

For your records, save your original sales receipt with this manual and write the product name below.


Spare parts

To order spare parts for this product, please visit our website

Was this article helpful?
0 out of 0 found this helpful