Skip to main content

GO•UP BABY LIGHTS (844-XXX)

Download the Manual

Click here to download the Manual in PDF format. Available in all languages.

Safety

20 kg max.: Seat mode (ride-on, walking bike)

50 kg max.: Scooter mode

Warnings

Seat mode: Not to be used by children over 36 months due to the limited strength of the seat bracket frame. The seat can only be used with this product when the steering is completely locked by the parents using the locking button located at the upper side of the steering assembly. Press down the locking button in order to lock the steering of the wheels when the seat is to be mounted

Warning! Protective equipment should be worn. Not to be used in traffic.

Remove the scooter and all the parts from the box. Set out all the parts and read the assembly instructions prior to use. Keep the packaging until assembly is complete.

General instructions​

This toy must be assembled by a responsible adult. Prior to use, make sure that the toy has been assembled properly. Remove all the parts which are not necessary for play before giving the toy to your child. The toy should be used with caution since skill is required to avoid falls or collisions causing injury to the user or third parties. To use with suitable protective equipment, including a helmet, shoes, elbow, wrist and knee protectors. Teach the child how to use it safely and responsibly

Directions​

  • The scooter can be dangerous and can cause traffic accidents when used on public highways. Don’t use on public roads. It is best used on a flat, clean surface, free of gravel and grease. Avoid bumps and drainage grates that may cause an accident.
  • The scooter does not include any headlights or lights. It is therefore not suited for use at night or during periods when visibility is limited.
  • Always use under adult supervision.
  • Do not allow more than one child to ride the scooter at the same time.
  • Do not use on wet days, or on wet ground.

Before and after each use​

  • Make sure that all locking mechanisms are securely locked.
  • Check the height of the steering system, and make sure the nuts are tightened and that the handlebars and the front wheel are perpendicular.
  • The minimum height of T-bar has to be locked at the lowest position by switching the bullet into the lowest hole (see diagram A).
  • Check all of the connection elements: the brake, the steering column’s quick release system and the wheel axles must be adjusted correctly and not damaged.
  • Also check the tyre wear.

Installation and use of seat for use of seat for ride-on/walking bike (See Page 2 in PDF)​

GO•UP BABY LIGHTS 360° comes with a sturdy seat support frame to better distribute the load of the seated child. There are 3 different seat heights available: 26.5-31.5cm. For a comfortable ride, your child’s feet should easily touch the footrest and the ground.

  • Place the footrest on the deck and under the seat support bar in the correct position (see diagram 1). Tighten the knob to make sure the footrest is securely in place.
  • Insert the seat support frame into the integrated tube hole at the front of the scooter deck between the two front wheels. Make sure to insert the seat support frame in the correct direction (see diagram 2) and ensure the spring ball on the front of the connector tube "clicks" into place, to securely hold the seat frame (see diagram 2a).
  • Attach the seat by sliding it on to the seat support frame. Select your preferred height, then tighten the knob to make sure the seat is securely in place (see diagram 3).
  • Install the backrest by sliding it at the rear of the seat and then tighten the screw to secure the backrest (see diagram 3a). Install the basket at the front of the seat, and make sure it "clicks" into place, to securely hold to the seat (see diagram 3b).
Warning!

Don’t overload the basket. 2kg max. Overloading the basket may cause a hazardous unstable condition.

Exert all your strength on the seat to check seat support bar is locked in place safely before riding.

Ride-on mode​

  • Insert the handlebar tube in the back hole of the backrest. Align the spring- loaded buttons with the notches at the rear of the backrest and lock the handlebars (see diagram 4). Double check that the spring-loaded button is engaged and locked correctly.
  • Adjust the height of the handle to the parent’s preference (4 positions are available; see diagram A). Loosen the quick release clamp of the T-bar handle when adjusting. Tighten the quick release clamp to secure the T-bar handle after adjustment.
  • Install the patented rear turning module under the deck of the scooter. Make sure you securely tighten the knob and engage the safety lock, in red, located on the knob (see diagram 5).
  • The parent handlebar and the rear turning module can be used to guide children during use. Place the child’s feet on the footrest and the adult pushes using the parent handle (T-bar). :::warning[Warning!] An adult must always hold the parent handle when the child’s feet are on the footrest and both hands are on the seat’s handlebars to avoid the child falling.

Make sure to always remove the patented rear turning module when the product is not used in ride-on mode. :::

Walking bike mode​

  • Remove the handlebar tube in the back hole of the seat by pressing the 2 spring-loaded balls.
  • GO•UP BABY LIGHTS 360° comes with an adjustable seat which can be adapted to the child’s height (3 positions). Unscrew the knob and slide up/ down to adjust the seat height. Align the seat through the screw holes in the connector tube and retighten the knob.
Warning!

Make sure children's feet can touch the ground freely in the seat mode before riding.

Steering: The child pushes with his feet on the floor to advance, while the child’s sitting on the seat. He must proceed with caution at first.

Notes​

  • Always check the body frame is securely inserted into the deck by pushing downward until you hear a "click".
  • Always check the seat knob is securely tightened.
  • To remove the footrest, first, unscrew the knob on the deck, then release the body frame from the deck by pressing the spring button on the front of the deck (see diagram 8).

Scooter Assembly (See Page 3 in PDF)​

  • Insert the T-bar column into the integrated tube hole at the front of the scooter deck between the two front wheels.
  • Make sure the spring ball on either side of the bottom of the column "clicks" into place for scooter mode.
  • Once the body frame is removed, cover the hole in the deck with the button in-pack (see diagram 10).
  • To release the T-bar or fold/unfold the scooter, step on the deck with your foot, press the spring-loaded button on the front of the deck and pull the T-bar column back at a 30-degree angle (see diagram 13-14).

Steering​

GO•UP BABY LIGHTS 360°’s steering responds intuitively to the movement of the body (see diagram B):

  • When the child leans to the right, GO•UP BABY LIGHTS 360° turns right.
  • When the child leans to the left, GO•UP BABY LIGHTS 360° turns left.

For younger children, on flat surfaces and in straight lines, GO•UP BABY LIGHTS 360° has a steering lock system to only go forwards and backwards for better balance and to make learning easier.

  • To lock, press the button atop the front of the deck (see diagram C).
  • To release, press the red button under the front of the deck (see diagram D).

During use​

  • Standing on the scooter, one hand on each handle, push with one foot to move forward. Proceed with caution at the start.
  • Braking: A brake is located at the rear; when necessary, press down on it to slow down. Press down gradually in order to prevent skidding or loss of stability.
  • Shoes are mandatory, and we strongly advise the child to wear trousers and long sleeve shirts to avoid injury in the event of a fall.
  • Explain to the child clearly how to use the scooter before any use.

GO•UP BABY LIGHTS 360° comes with a light LED module directly integrated in the seat’s handlebar

The different modes are: (see diagram 18)

  • ON: LED lights activated
  • OFF: LED lights disabled

Activating the light module on GO•UP BABY LIGHTS 360° (see diagram 17-18)​

  • Remove the module from the seat’s handlebar by turning it anti-clockwise.
  • Using the button, choose your preferred mode (OFF or ON).
  • Insert the module back into the seat’s handlebar and turn clockwise to lock it.
  • It’s advisable to switch the module OFF when not in use.

Important notice for GO•UP BABY LIGHTS 360° MODULE​

  • Module must be inserted in the seat’s handlebar before giving the toy to your child.
  • This product is powered by two built-in CR2032 lithium batteries.
  • This toy contains batteries that are non-replaceable. Replace the electronic module when the batteries are exhausted
Warning!

This toy produces flashes that may trigger epilepsy in sensitised individuals.

Care and maintenance​

Regular maintenance is a safety commitment:

  • Wheel bearings: Avoid going through water, oil, or sand as this can damage wheel bearings.
  • Wheels: The wheels wear down with time and can be damaged if overly used on rough surfaces. The back wheel on which the brake is applied is particularly affected after several hours of braking. In the interests of safety, they should be checked regularly and changed if necessary.
  • Modifications: The original product must by no means be modified except for the maintenance-related changes mentioned in these instructions.
  • Nuts and axles: These should also be checked regularly.
    • They can become loose after a while in which case they should be tightened.
    • They can become worn and not tighten properly, in which case they should be replaced.
  • Cleaning: Clean the scooter with a soft cloth and a little water.

Warranty​

The manufacturer warranties this product to be free of manufacturing defects for period of 2 years from the date of purchase. This limited warranty does not cover normal wear and tear, tire, tube or cables, or any damage, failure or loss caused by improper assembly, maintenance, or storage.

This limited warranty will be void if the product is ever:

  • used in a manner other than for recreation or transportation;
  • modified in any way;
  • rented

The manufacturer is not liable for incidental or consequential loss or damage due directly or indirectly to the use of this product.

Globber does not offer an extended warranty. If you have purchased an extended warranty, it must be honoured by the store at which it was purchased.

For your records, save your original sales receipt with the physical manual and write the product name below.

Additional info​

For questions and inquiries please contact us through the contact form.