Skip to main content

GO•UP ACTIVE ECOLOGIC (740-XXX)

Download the Manual

Click here to download the Manual in PDF format. Available in all languages.

Safety

20 kg max.: Seat mode (ride-on, walking bike)

50 kg max.: Scooter mode

Warnings

Seat mode: Not to be used by children over 36 months due to the limited strength of the seat bracket frame. The seat can only be used with this product when the steering is completely locked by the parents using the locking button located at the upper side of the steering assembly. Press down the locking button in order to lock the steering of the wheels when the seat is to be mounted

Warning! Protective equipment should be worn. Not to be used in traffic.

Remove the scooter and all the parts from the box. Set out all the parts and read the assembly instructions prior to use. Keep the packaging until assembly is complete.

General instructions​

This toy must be assembled by a responsible adult. Prior to use, make sure that the toy has been assembled properly. Remove all the parts which are not necessary for play before giving the toy to your child. The toy should be used with caution since skill is required to avoid falls or collisions causing injury to the user or third parties. To use with suitable protective equipment, including a helmet, shoes, elbow, wrist and knee protectors. Teach the child how to use it safely and responsibly

Directions​

  • The scooter can be dangerous and can cause traffic accidents when used on public highways. Don’t use on public roads. It is best used on a flat, clean surface, free of gravel and grease. Avoid bumps and drainage grates that may cause an accident.
  • The scooter does not include any headlights or lights. It is therefore not suited for use at night or during periods when visibility is limited.
  • Always use under adult supervision.
  • Do not allow more than one child to ride the scooter at the same time.
  • Do not use on wet days, or on wet ground.

Before and after use​

  • Make sure that all locking mechanisms are securely locked.
  • Check the height of the steering system, and make sure the nuts are tightened and that the handlebars and the front wheel are perpendicular.
  • The minimum height of T-bar has to be locked at the lowest position by switching the bullet into the lowest hole (see diagram A).
  • Check all of the connection elements: the brake, the steering column’s quick release system and the wheel axles must be adjusted correctly and not damaged.
  • Also check the tyre wear.

Installation and use of seat for use of seat for ride-on/walking bike (See Page 2 in PDF)​

  • GO•UP ACTIVE ECOLOGIC comes with a connector tube which is used to fix the seat. There are 2 different seat heights available: 25.4 and 28.7cm from the ground. For a comfortable ride, the child’s feet should easily touch the footrest and the ground.
  • Use the L-key in-pack to unscrew the handlebar. Insert the handlebar into the seat, and then tighten the screw to secure the handlebar.
  • Attach the seat to the connector tube by sliding it on to the tube. Select your preferred height, then tighten the knob to make sure the seat is securely in place (see diagram 1-2).
  • Insert the connector tube into the integrated tube hole at the front of the scooter deck between the two front wheels. Make sure to insert the connector tube in the correct direction following the arrow on the connector tube (see diagram 3) and ensure the spring ball on the side of the connector tube "clicks" into place, to securely hold the seat frame (see diagram 3).
  • Place the footrest on the deck in the correct direction. Make sure the knob is tightened and securely fixed (see diagram 5-6)
Warning!

Pull up the seat from the deck without pressing the side push-button on the deck to check that the seat connector tube is safely locked in place before use.

Ride-on mode​

  • Insert the handlebar tube in the back hole of the seat support frame. Align the spring-loaded buttons with the notches at the rear of the seat and lock the handlebars (see diagram 4). Double check that the spring-loaded button is engaged and locked correctly.
  • Adjust the height of the handle to the parent’s preference (4 positions are available; see diagram A). Loosen the quick release clamp of the T-bar handle when adjusting. Tighten the quick release clamp to secure the T-bar handle after adjustment.
  • The parent handlebar can be used to accompany children during use. Install the footrest (see diagram 5-6). Place the child’s feet on the footrest and the adult pushes using the parent handle (T-bar).

:::warning[Warning!] An adult must always hold the parent handle when the child’s feet are on the footrest and both hands are on the seat’s handlebars to avoid the child falling. :::

Walking bike mode​

  • Remove the handlebar tube in the back hole of the seat by pressing the 2 spring-loaded balls.
  • GO•UP ACTIVE ECOLOGIC comes with an adjustable seat which can be adapted to the child’s height (3 positions). Unscrew the knob and slide up/ down to adjust the seat height. Align the seat through the screw holes in the connector tube and retighten the knob.
Warning!

Make sure children's feet can touch the ground freely in the seat mode before riding.

Steering: The child pushes with his feet on the floor to advance, while the child’s sitting on the seat. He must proceed with caution at first.

Notes​

  • Always check the connector tube is securely inserted into the deck by pushing downward until you hear a "click".
  • Pull up the seat from the deck without pressing the side push-button on the deck to check that the seat connector tube is safely locked in place before use.
  • Always check the seat knob is securely tightened.
  • Remove the connector tube by pressing the side push- button on the deck.
  • To remove the footrest, unscrew the knob on the footrest, then remove the footrest. Once the footrest is removed, cover the hole in the deck with the button in-pack (see diagram 8-10).
  • A GLOBBER cap is provided to cover the hole behind the seat while in ride-on mode. This can be mounted onto the T-bar's column for storage (see diagram E).

Scooter Assembly (See Page 3 in PDF)​

  • Insert the T-bar column into the integrated tube hole at the front of the scooter deck between the two front wheels.
  • Make sure the two spring balls on either side of the bottom of the column "click" into place for scooter mode.
  • To release the T-bar or fold/unfold the scooter, step on the deck with your foot, press the push button on the side of the deck and pull the T-bar column back at a 30-degree angle. (see diagram 17-19).

Steering​

GO•UP ACTIVE ECOLOGIC’s steering responds intuitively to the movement of the body (see diagram B):

  • When the child leans to the right, GO•UP ACTIVE ECOLOGIC turns right.
  • When the child leans to the left, GO•UP ACTIVE ECOLOGIC turns left.

For younger children, on flat surfaces and in straight lines, GO•UP ACTIVE ECOLOGIC has a steering lock system to only go forwards and backwards for better balance and to make learning easier.

  • To lock, press the button atop the front of the deck (see diagram C).
  • To release, press the red button under the front of the deck (see diagram D).

During use​

  • Standing on the scooter, one hand on each handle, push with one foot to move forward. Proceed with caution at the start.
  • Braking: A brake is located at the rear; when necessary, press down on it to slow down. Press down gradually in order to prevent skidding or loss of stability.
  • Shoes are mandatory, and we strongly advise the child to wear trousers and long sleeve shirts to avoid injury in the event of a fall.
  • Explain to the child clearly how to use the scooter before any use.

Care and maintenance​

Regular maintenance is a safety commitment:

  • Wheel bearings: Avoid going through water, oil, or sand as this can damage wheel bearings.
  • Wheels: The wheels wear down with time and can be damaged if overly used on rough surfaces. The back wheel on which the brake is applied is particularly affected after several hours of braking. In the interests of safety, they should be checked regularly and changed if necessary.
  • Modifications: The original product must by no means be modified except for the maintenance-related changes mentioned in these instructions.
  • Nuts and axles: These should also be checked regularly.
    • They can become loose after a while in which case they should be tightened.
    • They can become worn and not tighten properly, in which case they should be replaced.
  • Cleaning: Clean the scooter with a soft cloth and a little water.

Warranty​

The manufacturer warranties this product to be free of manufacturing defects for period of 2 years from the date of purchase. This limited warranty does not cover normal wear and tear, tire, tube or cables, or any damage, failure or loss caused by improper assembly, maintenance, or storage.

This limited warranty will be void if the product is ever:

  • used in a manner other than for recreation or transportation;
  • modified in any way;
  • rented

The manufacturer is not liable for incidental or consequential loss or damage due directly or indirectly to the use of this product.

Globber does not offer an extended warranty. If you have purchased an extended warranty, it must be honoured by the store at which it was purchased.

For your records, save your original sales receipt with the physical manual and write the product name below.

Additional info​

For questions and inquiries please contact us through the contact form.