Learning Bike 2in1 (735-XXX)
Click here to download the Manual in PDF format. Available in all languages.
Not to be used by children over 3 years of age due to size limitation. Recommended that riders always wear a properly fitted helmet. Not to be used in traffic. 20 kg max.
Please carefully read the instructions before assembly and use the toy.
Be careful when unpacking and assembling the product.
Do not step or stand on back of frame which will cause product overturned.
Make sure children's feet can touch the ground freely before riding.
Do not use on wet days, or on wet ground.
Adult assembly only. The toy contained potentially hazardous conditions (small parts) in unassembled state.
Don't let your child access unassembled components until assembly is complete. Adult shall check regularly to ensure the item is assembled correctly to prevent collapsing during use.
General instructions of use
-
Prior to use, make sure that the product has been assembled properly. Check all the connection elements: The parent handle, footrest, saddle, and handlebar must be correctly adjusted, and make sure that the locking mechanisms are securely locked. Check the product before the child rides to determine if there are any potentially hazardous parts or conditions.
-
Children should be supervised by an adult while riding this product. Special care should be taken to instruct children in safe riding.
-
Do not use on public highways; to be used on flat and gravel-free areas (playgrounds, public squares, paved pathways, etc.).
-
Do not use this product near a staircase, on a slope, on a road, or on a wet surface.
-
As your child grows and gains more mobility, the potential for hazards increases. At home, be sure to remove frames or mirrors hung too low and that could break, and any object that could fall in the event of impact. A corner table can also be a danger.
-
Do not allow more than one rider on the product at a time.
-
Be sure the child wears clothes and appropriate footwear when using product.
-
Be sure the rider keeps both hands on the handlebars for proper control.
-
Do not allow the rider to wear anything that obstructs hearing and visibility or that impairs the functioning of the product.
-
The product should be used with caution since skill is required to avoid falls or collisions causing injury to the user or third parties
Protective equipment should be worn. Not to be used in traffic. Always wear safety equipment (helmet, elbow-pads, kneepads, gloves).
This toy has no brake.
Braking
The product can be slowed by the feet. The child can stop moving by stopping walking/pedalling. Please take care that your child can always stop from the speed he/she produces and wears appropriate shoes.
How to assemble LEARNING BIKE 2in1 (TRIKE mode)
-
Slot the front wheels’ head tube into the body frame of the LEARNING TRIKE 2in1.
-
Insert the handlebars’ stem onto the front wheels’ head tube; push the handlebars’ stem down. Make sure the handlebars are placed in the correct direction and push-in the handlebar. Pull up the handlebars to make sure they are securely fixed.
-
To install the saddle, unscrew the knob located on the side of the saddle, insert the saddle into the LEARNING TRIKE’s frame. Then, push the saddle down or up until you align with one of the holes. Tighten the knob. The saddle is adjustable with 2 heights (25.4cm; 26.7cm).
-
To install the rear wheels, insert the wide rear wheels’ subassembly into the LEARNING TRIKE’s frame. Make sure the black push-button located on the side of the frame is correctly inserted. Once it is in the correct position, make sure the rear wheels’ subassembly is secured by pulling on it.
-
To install the pedals, press and hold the red pedal release tab on the front wheel hub, insert the pedal into the hub aligning the slot in the pedal with the guide in the hub, release the tab, and push the pedal in (until you hear a click). Repeat the procedure on the other pedal. Check that the pedals are locked securely in place
Transform from TRIKE mode to WALKING BIKE mode:
- Press the push button located on the side of the stem of the LEARNING TRIKE’s frame to remove the rear wheel subassembly. Pull off the rear wheels’ subassembly from the LEARNING TRIKE’s frame.
- Insert the double-wide rear wheel subassembly into the LEARNING TRIKE’s frame. Make sure the black push-button located on the side of the frame is correctly inserted.
- Remove the pedals by pressing the red button located on each side of the front wheel. You can store the pedals at the base of the rear wheel subassembly when the product is not in use to avoid losing them
Maintenance and security
- Security checks: check periodically the product to identify any loose or dislocated element - particularly the wheels, saddle, and handlebars.
- Periodic cleaning will bring a good life. Wipe the product with a dry cloth if it has been soiled.
- Regularly check the condition of abrasion and avulsion.
- Regularly check that parts are not broken or damaged, if this happens, stop using this product.
- Regular checks can prevent an accident.
Warranty
The manufacturer warranties this product to be free of manufacturing defects for period of 2 years from the date of purchase. This limited warranty does not cover normal wear and tear, tire, tube or cables, or any damage, failure or loss caused by improper assembly, maintenance, or storage.
This limited warranty will be void if the product is ever:
- used in a manner other than for recreation or transportation;
- modified in any way;
- rented
The manufacturer is not liable for incidental or consequential loss or damage due directly or indirectly to the use of this product.
Globber does not offer an extended warranty. If you have purchased an extended warranty, it must be honoured by the store at which it was purchased.
For your records, save your original sales receipt with the physical manual and write the product name below.
Additional info
For questions and inquiries please contact us through the contact form.