Skip to main content

ONE K 165 DELUXE (672-XXX)

Download the Manual

Click here to download the Manual in PDF format. Available in all languages.

Safety

For 14 years old and above. 100kg max.

The scooter is reserved for adolescents and adults. It is not a toy, but sports equipment for physical training, it is not intended for use in extreme sports such as jumping, ollie ramps, etc. This product should never be used at a skate park for an “aggressive” use (challenging skateboarding moves, etc.).

Warnings

Use with caution on a flat, clean, dry surface and, if possible, away from other users, and obey the road safety rules.

Check local laws regarding scooter use, respect all the traffic rules and signs. Stay away from other pedestrians or users on public roads.

Best when used on a flat, dry surface free of gravel and grease.Avoid bumps and drainage grates that might cause an accident.

Warning! Protective equipment consisting of wrist protectors, gloves, knee pads, helmets and elbow pads should be worn.

Using the scooter​

Before and after each use​

  • To prevent pinched fingers, carefully follow the instructions of unfolding and folding. Make sure that the locking mechanisms are securely locked:
  • Check the height of the steering system and make sure that the nuts are tightened and the handlebars and front wheel are perpendicular.
  • Check all connected elements; the brake and the wheel axles must be correctely adjusted, and must not be damaged.
  • Also check the tire wear.

During use​

  • Standing on the scooter, with one hand on each handle, push with one of your feet to move forward. Proceed with caution at the start.
  • Shoes are mandatory and we strongly recommend wearing pants and long sleeve shirts to avoid injury if you fall.
  • The scooter does not include any headlights or lights. It is therefore not suitable for use at night or during periods when visibility is limited.

Braking​

  • A brake is located at the rear, when necessary, press down on it to slow down. Press down gradually to prevent skidding or loss of stability. The metal or aluminum brake may heat up after multiple uses. Avoid touching it during and after use.
  • A right handlebar brake is provided to decrease the speed of the scooter. When using, keep riding the scooter with both hands.

Assembling the product​

  • The folding and unfolding operations of the scooter are to be done by a single person.
  • During these operations, be careful you do not get your fingers stuck in the hinge and locking system.
  • Make sure that the locking devices are properly engaged.
Warning!

Risk of injury by pinching! Do not insert your fingers into the shaded area indicated in the image.

1 - Unfold the scooter​

Step 1: Unpack the folded-up scooter from its box.

Step 2: One hand is pressing down on the rear brake and the other hand pulls away the bar from rear brake . Unfold the handle and front wheel upwards until the automatic lock secures the T-bar handles in upright position.

Step 3: Open the clamp lever on the T-bar. Pull out both parts of the T-bar handle from the double clips. Press in the spring-loaded buttons and insert both into the tube of the T-bar. Wiggle and turn a bit until their spring-loaded buttons align with the holes and fix the whole steering bar assembly in place. Close clamp lever.

2 - Adjust the handle bar​

Open the clamp. Then press the spring-loaded button and pull the handlebar up or push it down with the other hand. Choose the suitable locking hole and make sure the spring- loaded button snaps securely in place. The adjustable T-bar handle can be adapted in height to suit the rider. Three different positions are available. Lock the clamp tight and securely when you have finished adjusting the height.

3 Positions:

  • Low position: 93 cm

  • Middle position: 100.5 cm

  • High position: 108 cm

3 - Folding the scooter​

  • Before folding the scooter, set the T-bar to the highest position and make sure the spring-loaded button snaps securely in place.

  • Both hands on the handlebars, giving a slight kick pedal lock as shown in the drawing 4. Fold back the T-bar handle until it locks on the back brake with an audible click, as shown in the drawing 5.

  • You can grip the scooter by the T-bar handle and pull it behind you for easy transport.

  • For storage purposes, remove both parts of the T-bar handle from the T-bar.

  • Open the clamp lever on the top of the handlebars, press down the spring-loaded buttons located on the top of the handlebars while pulling out the handlebars’ grip sideways at the same time. Strings inside the tubes will hold the individual handlebars’ grip together. Clip both grips of the T-bar handle into the clips on both sides of the steering bar.

DO NOT FORGET TO REGULARLY TIGHTEN THE DIRECTION BLOCKS TO AVOID MISALIGNMENT OR LOSS OF THE SCREW.

4 - Barrel adjustment for rear brake block: (see page 4)​

Fine tune the brake blocks by turning the barrel screw on the handlebar brake.

To do so, follow below instruction:

  • First undo the barrel-adjuster’s locknut by turning counter clockwise to untighten the locknut (see diagram A).
  • To move the brake blocks inward, unscrew the barrel by turning it counter clockwise in small increments to tighten the brake (see diagram B).
  • To move the brake blocks outward, screw the barrel inward by turning it clockwise in small increments to untighten the brake (see diagram C).
  • Regularly check the feeling of the brake to get the fine adjustment.
  • Tighten the barrel-adjuster’s locknut when done by turning it turn clockwise. (see diagram D)

Care and maintenance​

Regular maintenance is a safety commitment:

  • Wheel bearings: avoid going through water, oil, or sand as this can damage wheel bearings.
  • Wheels: the wheels wear down with time and can be damaged if overly used on rough surfaces. The back wheel on which the brake is applied is particularly affected after several hours of braking. In the interests of safety, they should be checked regularly and changed if necessary.
  • Modifications: the original product must by no means be modified except for the maintenance-related changes mentioned in these instructions.
  • Nuts and axles: these should also be checked regularly.
    • They can become loose after a while in which case they should be tightened.
    • They can become worn and not tighten properly, in which case they should be replaced.

Warranty​

The manufacturer warranties this product to be free of manufacturing defects for period of 2 years from the date of purchase. This limited warranty does not cover normal wear and tear, tire, tube or cables, or any damage, failure or loss caused by improper assembly, maintenance, or storage.

This limited warranty will be void if the product is ever:

  • used in a manner other than for recreation or transportation;
  • modified in any way;
  • rented

The manufacturer is not liable for incidental or consequential loss or damage due directly or indirectly to the use of this product.

Globber does not offer an extended warranty. If you have purchased an extended warranty, it must be honoured by the store at which it was purchased.

For your records, save your original sales receipt with the physical manual and write the product name below.

Additional info​

For questions and inquiries please contact us through the contact form.