ACE LIGHTS (667-XXX)
Click here to download the Manual in PDF format. Available in all languages.
For 4 years old and above. Not to be used in traffic. 100kg max.
The scooter is suitable for 4 years old or above. It is not a toy, but sports equipment for physical training, it is not intended for use in extreme sports such as jumping, ollie ramps, etc. This product should never be used at a skate park for an “aggressive” use (challenging skateboarding moves, etc.).
- Use with caution on a flat, clean, dry surface and, if possible, away from other users, and obey the road safety rules.
- Check local laws regarding scooter use, respect all the traffic rules and signs. Stay away from other pedestrians or users on public roads.
- Best when used on a flat, dry surface free of gravel and grease. Avoid bumps and drainage grates that might cause an accident.
Warning! Protective equipment consisting of wrist protectors, gloves, knee pads, helmets and elbow pads should be worn. T-bar folding and unfolding shall be done by an adult. The scooter can only be used by children once the adjustment is done. Do not allow more than one child to ride the scooter at the same time. Do not use on wet days, or on wet ground.
Before and after use
- Make sure that all locking mechanisms are securely locked:
- Check the height of the steering system, and make sure the nuts are tightened and that the handlebars and the front wheel are perpendicular.
- The minimum height of T-bar has to be locked at the lowest position by switching the bullet into the lowest slot.
- Check all of the connection elements: the brake, the steering column’s quick release system and the wheel axles must be adjusted correctly and not damaged.
- Also check the tyre wear.
SCOOTER ASSEMBLY (See Page 2 in PDF)
Insert the T-bar column into the integrated tube at the front of the scooter deck between the two front wheels. Make sure the two spring balls on either side of the bottom of the column "click" into place for scooter mode. To release the T-bar or fold/unfold the scooter, step on the deck with your foot, press the push button on the side of the deck and pull the T-bar column back at a 30 degree angle.
Adjust the height
Height adjustable handlebar which can be adapted to the child’s height.
- 5 Positions :
- Low position: 74.5 cm
- Middle position: 79.5, 84.5, 89.5 cm
- High position: 94.5 cm The bullet shall be in the hole while adjusting the T-bar height. Make sure that for the lowest position of the T-bar, the bullet is locked into the lowest slot (see ‘A’ diagram).
Steering
ACE’s steering responds intuitively to the movement of the body (Diagram B).
- When the child leans to the right, ACE turns right!
- When the child leans to the left, ACE turns left! For the youngest children, on flat surfaces and in straight lines, ACE has a steering blocking system for better balance and to make learning easier.
- To lock, press the button above (Diagram C).
- To release, press the red button below (Diagram D).
During use
- Standing on the scooter, with one hand on each handle, push with one of your feet to move forward. Proceed with caution at the start.
- Shoes are mandatory and we strongly recommend wearing pants and long sleeve shirts to avoid injury if you fall.
- The scooter does not include any headlights or lights. It is therefore not suitable for use at night or during periods when visibility is limited.
Care / Maintenance
Regular maintenance is a safety commitment:
- Wheel bearings: avoid going through water, oil or sand as this can damage wheel bearings. To look after the wheel bearings, systematically check that the wheels turn properly by turning the scooter upside-down and using your hand to spin the wheels. If the wheels do not spin they must be removed to check their condition. First unscrew the wheel axle, remove the axle and detach the wheel, then carefully push the two wheel bearings out of their housing. If they are chipped or dented, new ones should be bought. If there is no visible damage, they must then be oiled. To do this, remove all traces of grease, mud or dust with a kitchen towel or cloth, and re-oil them with a grease spray or by leaving them to soak overnight in oil [turn them several times in the oil first]. Then reassemble the wheel bearings and axles, followed by the wheel, onto the scooter. Proceed in the same manner for the other wheel.
- Wheels: the wheels wear down with time and can be pierced if overly used on rough surfaces. The back wheel on which the brake is applied is particularly affected after several hours of braking. In the interests of safety, they should be checked regularly and changed if necessary.
- Modifications: the original product must by no means be modified except for the maintenance- related changes mentioned in these instructions.
- Nuts, axles and other self-locking fixings: these should also be checked regularly. They can become loose after a while in which case they should be tightened. They can become worn and not tighten properly, in which case they should be replaced.
- Cleaning: Clean the scooter with a soft cloth and a little water.
Warranty
The manufacturer warranties this product to be free of manufacturing defects for period of 2 years from the date of purchase. This limited warranty does not cover normal wear and tear, tire, tube or cables, or any damage, failure or loss caused by improper assembly, maintenance, or storage.
This limited warranty will be void if the product is ever:
- used in a manner other than for recreation or transportation;
- modified in any way;
- rented
The manufacturer is not liable for incidental or consequential loss or damage due directly or indirectly to the use of this product.
Globber does not offer an extended warranty. If you have purchased an extended warranty, it must be honoured by the store at which it was purchased.
For your records, save your original sales receipt with the physical manual and write the product name below.
Additional info
For questions and inquiries please contact us through the contact form.